Of all the advice that I've discovered about building radios, the best piece of thus far has been to "Build it in modules, test the modules, then move on to the next part." So, naturally, after my success with building the audio amp earlier, I decided that I would tackle the VFO. After perusing several pages of schematics, HOURS of streaming video from YouTube and a few episodes of the Solder Smoke Podcast, I had settled on the Arduino controlled SI-5351 combo. Great! Lots of folks have build stuff with that combo.
Let's go back in time a few months: I started with Pete's (N6QW) "Lets Build Something" design. and acquired all the parts. I studied Pete's diagrams and poured over the articles in QRP Quarterly about it, plus his web page(s) about it. I managed to successfully build the circuit on a breadboard. After several hours of "fidgeting" with the Arduino's IDE due to my purchase of a copycat Arduino Nano, I finally got the computer talking to the chip. I copied Pete's code into the IDE and clicked the verify button only to be presented with a slurry of error messages talking about libraries. For the uninformed, confused, or just plain ignorant like myself... error messages are the digital equivalent to letting the "magic smoke" out of something, the only difference being you can fix it and use it again.
Whoa...pump the brakes kid. You got to get some street-smarts on this coding thing. So, down the rabbit hole I go. I spend the better part my precious shack-time the next few days learning about Arduino libraries; what they are, why they're used, and how they're used. I'm still clueless, but I have a little bit more of an understanding of the requirements at this point. So, I go fetch the required libraries, load up Pete's code again, click the verify button and get the proverbial "Good-to-Go" message. I clicked the upload button, waited for the chip to reboot and wouldn't you know it... I had a working VFO. At least in theory. Breadboard construction with wires hanging all over isn't really my style, so I put it on the back-burner and proceeded to continue with my other hobbies for a few months because there's furniture to build and freezers to fill.
Fast-forward to a few days ago.
With my renewed excitement about the CNC working, I decided to tackle the difficult part, at least for me, of my adventurous radio build. The VFO. I'd moved on from Pete's design. Not that there's anything wrong with it, I just found one that I like better. Enter Charlie Morris, (ZL2CTM) and his simple VFO/BFO. Charlie has a YouTube Video explaining the code, and that's the kind of info that I needed. I moved on to rebuilding Charlie's design on a breadboard, loaded up the code (changing Charlie's callsign to my own) and it worked. Awesome! Time to begin building the board in Sprint Layout. After a couple days, I had it down.
Not being one to make things easy, I decided that I needed to drill some holes in this board. That led down another whole-day of experimenting (Bill & Pete call it "noodling") with Sprint Layout and FlatCam software to make sure I could export, import, program and save the Excellon files to do it right without wasting too much copper. That lead me to thinking: How am I going to get power in and signals out of this thing? I had a few 78L05 voltage regulators in the junk-box, and googled how to build a basic voltage regulator. I was able to incorporate that onto the board as well. I noodled it out in short order and got to generating the CNC code.
I'd watched several other YouTube CNC videos where folks put blue tape on their spoilboard, and again on their part...sticky-sides out, then glued to tape-covered areas on the pieces to each other with superglue and accelerator. This...was a great idea and allowed me to stop using the dreaded "tabs" on my PCB material. While cutting out the board, I realized that all the text that I'd carefully placed in Sprint-Layout was entirely too small to be seen once cut out with a .1" 30-degree PCB bit. Cest' La Vie. No sense in wasting good copper doing it again.
With the spindle spinning, I could begin to imagine the smell of the solder melting already. The board was cut in short order on the CNC and I decided to get a good night's sleep before soldering the components to it. The next day I started soldering stuff up. I used pin-headers for the connections, but soon realized that I'd made a decision that I hope I won't regret. I soldered the pin-header to the Arduino board, and then couldn't figure out how to get my header-socket soldered and secure as well. In the end, I ditched the socket and just soldered the Arduino's pin headers directly to the board. Hopefully, I don't' fry it and have to replace it any time soon. If so, oh well. I'll snip them off one by one, then de-solder everything and start over.
Then I discovered the error of my ways. When I planned out the voltage regulator, I forgot to couple the filter caps to ground on the board. Instead, I put two isolated pads for each capacitor. Oops. Nothing a simple piece of wire can't fix, and I can just turn the caps sidewards and couple them to ground that way. It works, but might be a little "less than glamorous." I had planned for a similar "jumper" to cross another trace on the board for the mode switch, rather than route a trace all around the board.
I decided to use Charlie's PCB platform as a base, and glued that to a piece of 1/4" MDF that I had lying around in the woodshop that seemed about a good-size for a radio. Once everything was soldered on, I conducted some redneck-engineering and fashioned myself a panel for the display and the controls out of PCB protoboard. Its not pretty, its not symmetrical, but it works. I'll probably change it eventually once I figure out how to make a panel with the CNC. I mocked up a power port into a scrap piece of PCB that I'd cut for something else, and then ran wire to everything.
I got it all connected/soldered/wired and decided to go ahead and fire it up for testing. Following Pete's advice, I figured I'd tune for "maximum smoke". So, I set the adjustable power supply to 13.8V DC, said a quick, quiet, prayer to the Radio Gods and flipped the switch. No smoke, no pops, and I was graced with the red light on the Arduino and the "Juliano-Blue" glow of my LCD. Great! I plugged in the USB port to the Nano, loaded the code, and Voila! Bob, is definitely your Mother's Brother.
So, onward and upward. I have to do some more noodling and figure out what to do next. I might place the mixers on the board and wire them up (SBL-1's), or build the audio amp, or who knows. Progress is progress, and at least I'm off & running like a herd of turtles!
No comments:
Post a Comment